Clear Finish

$13.95$29.95

Clear Finish is an all natural, water based, non-yellowing varnish. Clear Finish is a thin translucent sealer that dries brilliantly clear. Clear Finish is formulated for ultimate clarity with a satin to glossy finish. Once fully cured, Clear Finish is water-resistant. Clear Finish is our recommended sealer for all pure and bright white painted finishes.

.

Clear Finish Tip Sheet

 

Clear selection

Description

Clear Finish is non-yellowing, NO VOC, NON TOXIC, water-soluble acrylic varnish designed for interior use only. Clear Finish is a thin translucent sealer that dries brilliantly clear. Clear Finish is formulated for ultimate clarity with a satin to glossy finish. Once fully cured, Clear Finish is water-resistant. Clear Finish is our recommended sealer for all pure and bright white painted finishes. Also, recommend over cabinets, foils, metallics, or anything requiring higher sheen level.

Recommended Use:

Clear Finish is formulated to seal and protect painted indoor surfaces. To maintain shimmer and shine, Clear Finish is perfect for sealing Pearl Plaster and metallic leafing or foils. Clear Finish is designed to be used on a variety of surfaces including furniture, walls, and most cabinetry. Clear finish is not recommended for outdoor use. The more coats of Clear Finish, the glossier the finish for more modern aesthetics.  Since dried Clear Finish can sometimes have a glossy characteristic depending on the amount of coats applied, it is not recommended on floors. Do not use on surfaces previously sealed or to be sealed with wax. To add an additional sealer over waxed surfaces  or to seal floors we recommend Clear Topcoat Sealer by Artisan Enhancements ®.

Application:

Make sure the surface is cleaned and sealed before painting to avoid any unwanted bleeding or reaction. Allow the surface to fully dry overnight after painting. Stir Clear Finish thoroughly before each application. Using the 45MM Topcoat Brush by Artisan Enhancements®, specialty varnish roller, or a quality flat edge varnish brush – apply 1 very THIN coat. The coats should look “wet” not “milky”. If the layer of Clear Finish looks milky, too much product has been applied. If this happens, “off-load” excess Clear Finish from the tool and attempt to lightly distribute excess product on the surface with the tool (working the excess Clear Finish into unsealed areas of surface). Allow the first coat of Clear Finish to fully dry before applying a very thin 2nd coat. For optimal results let the first coat dry for 24 hours before applying second coat. The sealed surface should be fully dry to touch after 12 hours depending on the moisture in the environment. Allow surface to cure a minimum of 48-72 hours before use.

 

Note: If more sheen or gloss is desired, add an additional thin coat of Clear Finish after the first two coats have been allowed to fully dry. Clear Finish can range between a soft satin (just above a matte) to glossy finish. We recommend working Clear Finish into your surface with even controlled strokes. The glossier the finish the more apt it will be to show brush strokes.

 

Helpful Hints- Why does the surface sealed with Clear Finish still feel “moist” or look “cloudy” after 24 hours?

If the sealed surface does not dry quickly or looks cloudy one of the following reasons could be the cause:

-The coats of Clear Finish were not thin enough and too much product has been applied. This is a

common issue usually stemming from the incorrect tool or not off-loading excess product from the tool before applying the sealer to the surface. If too much Clear Finish was used – extend the dry and cure time until surface no longer feels moist.

-A cloudy look is usually the result of the second coat being applied before the first coat was completely dry. Extend the dry and cure time until surface no longer looks cloudy.

– If you get a ring or water spot on your surface because your surface has not fully cured, let the spot or ring dry out on its own. There is no need to “clean” the area.

Clean up & Product Storage: Easy clean up with soap and water. Seal the container tightly. Do not let freeze or expose to direct sunlight/extreme heat. Do not apply product when air and surface temperatures are below 50°F (10°C).

Additional Resources and Inspiration:

http://artisanenhancements.com/blog/

https://www.pinterest.com/artisanenhance/clear-finish-by-artisan-enhancements/

https://www.pinterest.com/artisanenhance/all-natural-sealers-and-topcoats-by-artisan-enhanc/

Additional information

Size

1qt, 8oz

Reviews

There are no reviews yet.

Be the first to review “Clear Finish”

You may also like…